Fluke Kohoutovice

Technology of laying gypsum tiles along with your hands

Gypsum tiles must be laid correctly, as not just the aesthetic look of cosmetic facing, but in addition the service life of this

substance will be dependent on the technologies of job. The product is universal, and it may be attached to plaster, concrete,

brick or gypsum board sheets, provided the top layer of the base is and has no defects.

If the defects of this base are important, it ought to be completely treated with primer, then a cement mortar is created, which

fills all of the cracks. Subsequently the surface ought to be repeatedly primed and dried. In this case, its composition should

decide on a particular, comprising elements which stop the appearance of fungus and mould.

In the modern interior of the rooms most frequently used gypsum tiles, imitating natural stone or brick. To perform cosmetic

finishing yourself, it is necessary first of all to select a strategy of tile placement and prepare a remedy. It’s crucial to pay

attention to the opposite side of the material. If its surface has an embossed surface, then the adhesive should be placed having

an trowel, and if it is even, then with a notched one.

The technology of this job is as follows:

* A thin layer of adhesive mortar is placed on the pre-prepared wall. It is distributed over the bottom so it is likely to place

4-5 tiles. Decorative cladding may be placed either on plasterboard, and on putty.

* Glue the rear side of these tiles with adhesive.

* Plaster components are pushed against the walls and their place is corrected. To align with the seams, it is recommended to

use spacers.

* Finishing is performed in rows, all which should be changed by half of a tile. Facing is carried out into the corners of the

room, then immediately eliminate any remaining mortar in the joints.

Drying the walls requires no more than a day also requires a constant humidity and temperature within the room. The last point in

the placing of gypsum tiles is their own decoration. To do this, the joints between the elements are filled with a special

solution, the color of which matches the brick.

Cosmetic fake of brickwork around the walls is carried out in the following manners:

* Cutting the plastered surface of the stitches of masonry using a bolt cutter with your hands;

* placing of tiles under the brick:

* imitating the format and color of the side of one brick;

* Imitating a fragment of brickwork of several bricks.

The best way to decorate“under the brick“ is really the one which allows you to make a practical coating with the maximum look of

its similarity to organic masonry. All 3 ways to carry out this type of finishing functions fulfill the prerequisites, however,

the cutting of joints using a bolt is more labor-intensive and the creation of considerable amounts of dust, so let us consider

more prevalent manners.

The old finish is removed from the walls, and also the outside, if needed, is leveled to get rid of the need to paste plaster on a

thick layer of adhesive.

Combining these cladding with different kinds of interior finishes could be both orderly and done with no apparent consistency,

chaotically, with fake of indications of aging.

With the support of decorative gypsum tiles it is possible to imitate a lot of textures.

A large number of textures may be imitated with the help of cosmetic gypsum tiles.

The wall where it’s to be set up must possess the following characteristics:

* Hardness and strength of the surface;

* masterfasada.ru The absence of irregular locations and sharp gaps;

* no deformations.

Decorative tiles at the interior of this kitchen

Walls are created from a variety of materials, let us break down the principles of setup.

When dealing with concrete, there’ll be no big problems. It’s only required to take into account the porosity of the material.

Concrete, that has almost no pronounced pores, ought to be treated with a good primer.

Mounting gypsum tiles on concrete

Before beginning work on the installation of gypsum tiles to the walls, then it’s worth assessing the strength of this surface.

When the plaster doesn’t drop off the walls and at the same time holds well, you can simply paint it using primer.

Mount the tiles onto the painted concrete should not. The surface ought to be scratched, making sure to misfire, then it ought to

be grouted and covered with a layer of plaster.